Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. You should post this problem in the Mustang section. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... It is not in the Chilton's manual.My husband thinks the relay contacts are welded and that happened when he re hooked the battery up.Thanks Expert: chris replied7 years ago. http://win8s.com/ford-escort/ford-escort-zx2-ac-not-working.html
relays, not sure how to check those or even where they are located... The wiper & blower motor are tied together at the blower motor relay, per the schematic. Its hidden up behind the dashboard, somewhere above the fuse box on the left kick panel. You said that I could probably use my actual switch.
After sanding away some rust, down to shiny metal - then the motor worked again. Is the resistance less than 5 ohms? You can only upload a photo or a video.
The resistance to electrical flow creates heat which in-turn melts the harness. 2) The motor is drawing too much amperage. There are 3 bolts that go into the aluminum casting, and three more bolts that hold the steel bracket to the cowling. Locate and disconnect the interior fuse panel connector. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading...
Close Yeah, keep it Undo Close This video is unavailable. Loading... Thanks, XXXXX XXXXX that. No GO to WW2.
Yes No Sorry, something has gone wrong. This fix is for a 1991-1996 Ford Escort (Mine was a GT, but all use the same relay). any settins wipers wont work... Problem eventually ceased altogether.
WW16 CHECK FRONT WIPER MOTOR POWER SUPPLY Key ON (will not operate in ACC). Both times I had to also clean up the metal mounting legs. Here's are the wiring diagrams. retrochad 18,256 views 2:02 Changing Fuel Injectors 1999 Ford Escort - Duration: 6:00.
WW14 CHECK FRONT WIPER SWITCH OPERATION Disconnect the front wiper switch connector. http://win8s.com/ford-escort/ford-escort-horn-not-working.html WW18 CHECK INTERVAL GOVERNOR PARK CIRCUIT Disconnect the interval governor connector. What does that say about the govenor at this point? roadragecustoms 334,797 views 3:23 91-96 Ford Escort thermostat 1.9L replacement - Duration: 5:23.
Is the resistance less than 5 ohms? Working... everything looks fine, but not working, i had a friend check out the connections and he said they should be getting power, could it be the wiper switch? his comment is here WW12 CHECK INTERVAL GOVERNOR OPERATION Interval governor connected.
I will respond back and accept after he gets a look at the car in the daytime, ok?Thanks again for any suggestions. Have you checked fuse 26? I've checked all the wiring, fuses, etc.
Disconnect the interval governor connector. Expert: fordman312009 replied7 years ago. Sign in Transcript Statistics 41,475 views 168 Like this video? Flag inappropriateSign in to replySign in to Write an AnswerRelated Items:blower motor relayWhere would blower motor relay be located?Ford shop manual I have says 30amp fuse is located dr...1 answerJanuary 17,
J S 4,316 views 4:59 Auto Repair : How to Test a Windshield Wiper Motor - Duration: 3:04. They would work again) Finally when it failed for good, it would not work in intermittent, low or high. You can only upload a photo (png, jpg, jpeg) or a video (3gp, 3gpp, mp4, mov, avi, mpg, mpeg, rm). weblink Changes gaskets, control module.
I am frustrated by this. The interval governor is controlled by the stalk on the steering column, and gets its voltage from the same 20 amp fuse labelled 'wiper'. * Just because the wiring manual for Please try again later. But, we think the intermittent windshield wiper relay appears to be shorted making the wipers run all the time.