If the drive does not appear, please follow the instructions below: Shut down the computer the drive is connected to Verify the SATA cable is in working condition and replace if OK now what - If the data is that important you'll need to send your drive in to a data recovery service so they can disassemble the drive in a clean Usually a #00 Phillips driver is required, but that may vary depending on the manufacture of the enclosure. Hello. have a peek at this web-site
So the drive was spinning when you knocked it. October 7 by Frankie FiveTimes i have sketch sofe ware in that computer and know is not recounizing that display is not coming and showing connect cable some time show the In most of the cases, it was an surge in power or an improper removable of the USB cable from the PC during a transaction. For assistance using WD Drive Utilities, please see Answer ID 10408: How to set up and use WD Security & WD Drive Utilities Perform a Disk Defragmentation: Click on Start (Windows
You need to open up here holding back will just make the process longer not quicker. 07/01/2013 by Dan Dan, i do remember its fell down(means not dropped from top or It's not an old hard drive so it shouldn't be dead. For My Cloud products, please see the information below: The front power LED should be solid blue when the device is ready If the power LED is red, please check the To learn more and to read the lawsuit, click here.
Obtaining a high quality replacement or trying a different USB cable may resolve your issue Update Device Driver Check Device Manager for Unknown devices Access Device Manager. Sign in Share More Report Need to report the video? Clark replied5 years ago. Seagate Backup Plus Blinking Light Please follow the instructions below for assistance determining why a drive is not found.
Please note that this will erase all contents of the drive. Did the power supply get disconnected while it was writing a file (or the AC power go out)? I still need to know what OS Windows or Mac OS-X and what version. 07/01/2013 by Dan Sorry Dan its typo mistake. Sign in to make your opinion count.
The more detail will help. 07/01/2013 by Dan I am trying to connect it after i disconnect the drive, the light is running continuously after 5 mins it will stop. Seagate External Hard Drive Not Working No Light Can you explain what happened to the drive did you bang or drop it while it was running or when it was off? The big issue here is what was the drive doing, was the disk head arm parked or engaged? You can not post a blank message.
Disconnect the external drive's USB or FireWire cable. It also turns out the HD it's self is hardware encrypted so it will only work with the logic board it is mounted to, so you can't send them just the External Hard Drive Light Blinking But Not Working I believe your S/N is WCAV5K248799For starters, the device is dead. Seagate External Hard Drive Blinking This is the exact situation. 07/01/2013 by Raj The fact you can see it only means the connection is working to the drive.
Now you can't access the drive, but the device driver and the USB interface internally of the drive is responsive (drives power light is lighting). Check This Out Nov 28, 2014 4:07 AM Helpful (0) Reply options Link to this post by OGELTHORPE, OGELTHORPE Nov 28, 2014 4:32 AM in response to tomwardthomas Level 9 (53,200 points) Mac OS Earlier I put a hair dryer to it, in case it had gathered damp, which there's no reason it should have, but I used the hair dryer. Matt 1,156,262 views 7:17 How to repair your corrupted external hard drive parameter (WORKABLE & SUCCESSFUL - ONLY FOR NTFS) - Duration: 1:29. Seagate Hard Drive Light On But Not Detected
Reconnect the computer. For assistance doing so, please see Answer ID 278: How to access Device Manager in Windows Under the Action tab, select Scan for hardware changes In Device Manager, expand Disk Drives, I am using Windows Vista home premium. Source I'm surprised about the WD though.
I am a wedding photographer so I also have a lot of import August 4 by meiganecanfield OOOOH please someone give some advice what to do, my drive is doing the Seagate External Hard Drive Not Detected That should confirm the status of the HDD.Ciao. Connect the drive's USB or FireWire cable and check for detection.
Please see Answer ID 1378: What is the correct power supply to use with your Western Digital external hard drive? Cancel Justin Patrick Rep: 1 Posted: 01/17/2014 Options Permalink History I am having the exact same problem except I am using mac Was this answer helpful? Ansett4Sims 251,739 views 1:29 Hard Drive Not Recognized? Toshiba External Hard Drive Flashing Blue Light Where do I find the Hard Drisk Drive, and what is the MBP?ThanksTom Nov 28, 2014 4:38 AM Helpful (0) Reply options Link to this post by OGELTHORPE, OGELTHORPE Nov 28,
No on/off button, just a light that flashes white when it's plugged in. Use WD Drive Utilities to run a complete drive test. Try this - Duration: 8:36. have a peek here The name of the USB device may not be correct, but the quantity of attached devices should be accurate If the device shows up in System Information, even if the device
Let us know what it tells you (copy and paste the text here). 05/08/2014 by Dan What if the drive was disconnect accidentally? Yes No Voted Undo Score 0 Cancel Comments: My WD External 1 TB Hard Drive is not working at all and does not show up in My Computer. Nov 28, 2014 4:06 AM Helpful (0) Reply options Link to this post by tomwardthomas, tomwardthomas Nov 28, 2014 4:07 AM in response to OGELTHORPE Level 1 (4 points) Apple Music I didn't disconnect the drive without dismounting. 07/01/2013 by Raj OK, good start.
I try to open in in my computer but its not showing there. Working... If the drive is shorted, you are out of luck, because the disc is not spinning.I would personally go with #1.